How to find weight in autodesk inventor [Best Article]



Last updated : Sept 1, 2022
Written by : Kasey Zank
Current current readers : 2319
Write a comment

How to find weight in autodesk inventor

How do you find weight in Inventor?

Q: How do I determine the mass of my parts in Inventor? On the iProperties dialogue, click on the Physical tab (you may need to click update). Your Mass, Area and Volume are displayed below.

How do I view properties in Inventor?

From the menu, select File iProperties to display the iProperties for the active file. Right-click a referenced file in the browser, and then select Properties to display its iProperties.

How do I see volume in Inventor?

  1. Step 1 – Prepare your Model. To start, you will use the Copy Object command to make a duplicate of our solid part as a surface object.
  2. Step 2 – Patch the Holes.
  3. Step 3 – Sculpt the Internal Volume.
  4. Step 4 – Checking the Physical Properties.

How do you find an objects weight?

The weight of an object is defined as the force of gravity on the object and may be calculated as the mass times the acceleration of gravity, w = mg. Since the weight is a force, its SI unit is the newton.

How do you calculate an objects weight?

The equation used to calculate the weight of an object is F = ma. "F" is the force in Newtons, "m" is the mass in grams and "a" is the acceleration due to gravity. Put the values of the problem into the equation. For example, multiply the mass of the object times the acceleration due to gravity, or F=(3g)(9.81 m/s^2).

How do I find my CAD scale?

  1. Click View tab Viewports panel Scale Monitor. Find. The Scale Monitor dialog box is displayed.
  2. In the drawing area, move the cursor over the scale area (or a viewport ) and check the Scale Monitor dialog box.
  3. Press ENTER to exit this command.

How do you find your takeoff weight?

As a basic example you can look at flight in the following way: DOW (aircraft weight) + Payload (passengers/cargo) = Zero Fuel Weight. Add the amount of fuel we're carrying = Take-Off Weight. How much fuel we burn enroute gives us our landing weight: TOW – Trip Fuel = Landing Weight.

How do you calculate CAD scale?

  1. Choose your scale. For example: 1/4” = 1”
  2. Invert the fraction and multiply by 12 to get: 4/1 x 12 = 48.
  3. Your scale factor is 48.

How do I see mass Properties in Autodesk Inventor?

Open the iProperties for the part, then click the Physical tab. Make sure the Material is set correctly. The mass is shown in the properties near the middle of the dialog box. If it is showing as N/A, click the Update button and it should fill in.

How do I check file Properties?

To view information about a file or folder, right-click it and select Properties. You can also select the file and press Alt + Enter . The file properties window shows you information like the type of file, the size of the file, and when you last modified it.

How do I find Properties in CAD?

Enter CUI on the command line. Select your workspace on the left. Click the Customize Workspace button on the right. Expand Palettes and select Properties.

How do you check volume?

To find the volume of a box, simply multiply length, width, and height — and you're good to go! For example, if a box is 5×7×2 cm, then the volume of a box is 70 cubic centimeters.

How do you show scale in Inventor drawing?

Create a Custom View Scale In the left pane of the Style and Standard Editor dialog box, select the active drawing style (displayed in bold text). In the Preset Values group, select Scale from the dropdown selection list, and then click New. Enter a new scale in the Add New Scale dialog box. Click OK.

Can you Measure in Inventor view?

You need an Inventor Viewer to open Inventor assembly, part or drawing files in a read-only mode to view, measure and print.

How do you find the mass and weight of an object?

  1. Mass=density*volume (m=ρV)
  2. Mass= force/acceleration (m=F/a)
  3. Mass= weight/gravitational acceleration (m=W/g)

How do you find weight of an object without a scale?

Place the object you want to weigh in 1 cup, then fill the other cup with water until it balances with the object. Then, measure the amount of water you put in the cup in milliliters. The number of milliliters of water will equal the number of grams the object weighs.

How do you find weight from area?

Once you have the measurements for the sectional area, length and density of your metal, you can now determine the weight using the following metal weight calculation formula: Weight (kg) = Sectional Area (mm2) x Length (m) x Density (g/cm3) x 1/1,000.

What is scale command in CAD?

It allows us to resize lines, polylines, and shapes. It's typically used to increase or decrease an object's size by using multiplication and division. The Scale command can also be used with references, and we can specify specific points to set an object's size.

How do you find the scale of a viewport?

  1. Click the Model tab.
  2. Click a viewport to make it current.
  3. Choose View > Zoom > Zoom.
  4. Type the zoom scale factor relative to paper space by appending the suffix xp to the scale factor, and then press Enter.

How do you scale a drawing?

To scale a drawing by hand, start by measuring the width and height of the object you'll be scaling. Next, choose a ratio to resize your drawing, such as 2 to 1 to double the image in size. Then, multiply your measurements by the first number in your ratio to increase the size.


more content related articles
Check these related keywords for more interesting articles :
3d furniture design cost
Software architecture performance tactics
Pcb design and testing software
How to draw stairs in vectorworks
How to make sketchup level
How to install octane render for cinema 4d r25
How to launch skp file
How to export from sketchup web
How to use piezo in tinkercad
Software architect role in agile
How to change level revit
How to use doors in sketchup
3d model drone camera
How to change revit view scale
How to check angle in archicad








Did you find this article relevant to what you were looking for?


Write a comment




How to find weight in autodesk inventor


Comment by Fidelia Cuascut

so one of the new things we're gonna do here is we're going to change the material type of our part we're gonna incorporate part a parts list that includes information about the volume and mass the soya can know if you've created the part correctly and then I want to check every individual dimension I can just tell if you've created the correct volume part now you know tell me about all the dimensions at once and then I can tell if you've changed the material type by just checking the mass all right so what we do is go back to our part and it's only one click really so this menu up here what we've been using here for default is color but this one just to the left of it is in the material type for the this first part click on the arrow I want you to change it to aluminum 6-0 6-1 so I scroll to the top or aluminum is and just choose aluminum 6-0 6-1 see the part automatically changes color indicates that this is now aluminum and we save that we have to make sure to save so that when we go back to our drawing now I can see our drawing has changed a little bit and so just like we've always done we put in a parts list um and it is for practice part one say open say okay put it in the upper right corner alright so that's it and then we do have to update it or change it so we right go over to the menu click on edit part parts list and we want to choose our columns so we want to get rid of the description remove that um and what we want to do is we want to scroll down until you find volume I want to include that first click Add and then we go up to mass and that say okay apply and okay so now I can tell that it's if it's correctly built it will have a mass I start a volume of sixteen point five thirty one cubic inches and if you've also built it right and created selected the correct material type it will have a mass of one point six one three pound mass and that is officially it


Thanks for your comment Fidelia Cuascut, have a nice day.
- Kasey Zank, Staff Member


Comment by potten9

Thanks for this interesting article


Thanks potten9 your participation is very much appreciated
- Kasey Zank


About the author